-- *****************************************************************
-- CISCO-IF-CAPABILITY.my: Cisco IF-MIB AGENT-CAPABILITIES
--
-- February 2004, Yizhong Shen
--
-- Copyright (c) 1998, 2000, 2002-2004, 2006, 2008
-- by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************CISCO-IF-CAPABILITY DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITYFROM SNMPv2-SMI
AGENT-CAPABILITIESFROM SNMPv2-CONF
DisplayString,TruthValueFROM SNMPv2-TC
ciscoAgentCapability
FROM CISCO-SMI;ciscoIfCapability MODULE-IDENTITYLAST-UPDATED"200803170000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com
cs-lan-switch-snmp@cisco.com"DESCRIPTION"Agent capabilities for IF-MIB"REVISION"200803170000Z"DESCRIPTION"Added ciscoIfCapabilityc4710aceVA1R700
agent capabilities for ACE 4710 Application
Control Engine(ACE) Appliance."REVISION"200611030000Z"DESCRIPTION"Added ciscoIfCapabilityIOSXRV3R4CRS1 agent
capability for IOS XR 3.4"REVISION"200610300000Z"DESCRIPTION
"Added capability for Cisco TelePresence System (CTS) and
Cisco TelePresence Manager (CTM) platforms."REVISION"200607170000Z"DESCRIPTION"Added ciscoIfCapabilityACSWV03R000 agent capabilities
for Cisco Application Control Software (ACSW) 3.0."REVISION"200602020000Z"DESCRIPTION"Added ciscoIfCapabilityIOSXRV2R0CRS1 agent capabilities
for IOS XR release 2.0."REVISION"200408090000Z"DESCRIPTION"Added ciscoIfCapabilityV5R015 agent capabilities for MGX
product series: MPSM Service Module and VXSM (Voice Switch
Service Module)."REVISION"200402210000Z"DESCRIPTION"Added following Agent capabilities for Catalyst
6000/6500 and Cisco 7600 series devices:
ciscoIfCapabilityCatOSV08R0101 and
ciscoIfCapabilityCatOSV08R0301."REVISION"200402200000Z"DESCRIPTION
"Added ciscoIfCapabilityV5R00 agent capabilities for MGX
product series: MPSM Service Module and VXSM (Voice Switch
Service Module."REVISION"200303140000Z"DESCRIPTION"Added following Agent capabilities for MGX product series:
- ciscoIfCapabilityV4R00 for
AXSM 10 Gig. Module (AXSM-XG) and
AXSM Enhanced Module (AXSM-E)."REVISION"200206120000Z"DESCRIPTION"Added following Agent capabilities for MGX product series:
- ciscoIfCapabilityPxmVR200 for
PXM(Processor Switch Module) Module
- ciscoIfCapabilityAxsmVR200 for
AXSM(ATM Switch Service Module)
- ciscoIfCapabilityAxsmeV21R60 for
AXSM Enhanced Module.
- ciscoIfCapabilityFrsm12V3R00 for
Frame Relay Service Module(FRSM-12)."REVISION"200002090000Z"DESCRIPTION"Modification of ifCounterDiscontinuityTime,
ifTableLastChange object and LinkUp/Down trap
objects."REVISION"9811160000Z"
DESCRIPTION"Initial version of this MIB module."::={ ciscoAgentCapability 125}ciscoIfCapabilityV11R03 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco IOS 11.3"STATUScurrentDESCRIPTION"IF MIB capabilities"SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifStackGroup2,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifRcvAddressGroup,
ifOldObjectsGroup
}VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
ACCESSread-writeDESCRIPTION"Can not be written in case of atm/aal5
sublayers on an ATM end system, LEC subinterfaces,
aal5 sublayer of an ATM switch CPU interface,
ATM 2000 physical interface and lex based interfaces
used for accounting."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3),
unknown(4),
dormant(5)}DESCRIPTION"Unable to detect all states."
VARIATION ifLastChange
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces, lex based interfaces
used for accounting. In case of subinterfaces, the value
returned will be the sysuptime when the subinterface
registered with ifmib."VARIATION ifInOctets
ACCESSread-onlyDESCRIPTION"Not supported in atm sublayer on an ATM end system.
Supported in physical interfaces, lex based interfaces,
aal5 sublayer of an ATM switch CPU interface,
aal5 sublayer on the atm interfaces of an ATM
end system, AIP type aal5 sublayer on an ATM
end system and in frame-relay, x25,
aflane subinterfaces."VARIATION ifInUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface, aflane sublayers."VARIATION ifInNUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifInDiscards
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface, aflane sublayers."VARIATION ifInErrors
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface, aflane sublayers."VARIATION ifInUnknownProtos
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical
interfaces, lex based interfaces, aal5
sublayer of an ATM switch CPU interface,
aflane sublayers."VARIATION ifOutOctets
ACCESSread-onlyDESCRIPTION"Not supported in atm sublayer on an ATM end system.
Supported in physical interfaces, lex based interfaces,
aal5 sublayer of an ATM switch CPU interface,
aal5 sublayer on the atm interfaces of an ATM
end system, AIP type aal5 sublayer on an ATM
end system and in frame-relay, x25,
aflane subinterfaces."VARIATION ifOutUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface, aflane sublayers."VARIATION ifOutNUcastPkts
ACCESSread-only
DESCRIPTION"Supported in physical interfaces, lex based accounting
interfaces and in aflane subinterfaces."VARIATION ifOutDiscards
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface, aflane sublayers."VARIATION ifOutErrors
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface, aflane sublayers."VARIATION ifOutQLen
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifSpecific
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifInBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCInOctets
ACCESSread-onlyDESCRIPTION"Supported in LEC sublayers only."VARIATION ifHCInUcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCInBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCOutOctets
ACCESSread-onlyDESCRIPTION"Supported in LEC sublayers only."VARIATION ifHCOutUcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifLinkUpDownTrapEnable
ACCESSread-writeDESCRIPTION"Only physical interfaces can have link traps enabled.
Hardwired on subinterfaces and on lex based interfaces
used for accounting to be false."VARIATION ifPromiscuousMode
SYNTAXTruthValueACCESSread-onlyDESCRIPTION"Not writable, hardcoded to false (2)."VARIATION ifConnectorPresent
ACCESSread-onlyDESCRIPTION"Hardcoded to be true for controller
type sub-interfaces and to be false for
all other sub-interfaces."VARIATION ifAlias
SYNTAXDisplayString(SIZE(0..64))
ACCESSread-writeDESCRIPTION"For interfaces that are not being nv written,
the ifAlias value is lost when the system is
reloaded."VARIATION ifCounterDiscontinuityTime
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifStackStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Write/create not supported.
Unable to detect all states."VARIATION ifRcvAddressAddress
DESCRIPTION"Read-only access is added to this object.
Supported in physical interfaces, lex based
interfaces and in lec sublayers."VARIATION ifRcvAddressStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Write/create not supported. Unable to detect
all states. Supported in physical interfaces,
lex based interfaces and in lec sublayers."VARIATION ifRcvAddressType
SYNTAXINTEGER{
other(1)}ACCESSread-onlyDEFVAL{ other }DESCRIPTION"Write/create not supported. Unable to detect
all states. Default value is { other }.
Supported in physical interfaces,
lex based interfaces and in lec sublayers."
VARIATION ifTestId
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestStatus
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestType
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestResult
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestCode
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestOwner
ACCESSnot-implementedDESCRIPTION
"Table for ifTestEntry not supported."VARIATION linkUp
DESCRIPTION"A linkUp trap signifies that the sending
protocol entity recognizes that one of the
communication links represented in the agent's
configuration has come up."VARIATION linkDown
DESCRIPTION"A linkDown trap signifies that the sending
protocol entity recognizes a failure in one of
the communication links represented in the
agent's configuration."::={ ciscoIfCapability 1}ciscoIfCapabilityV12R00 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco IOS 12.0"STATUScurrentDESCRIPTION"IF MIB capabilities"SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifStackGroup2,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifRcvAddressGroup,
ifOldObjectsGroup
}VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
ACCESSread-writeDESCRIPTION"Can not be written in case of atm/aal5 sublayers
on an ATM end system, LEC subinterfaces, aal5
sublayer of an ATM switch CPU interface, ATM 2000
physical interface and lex based interfaces used
for accounting."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3),
unknown(4),
dormant(5)}DESCRIPTION"Unable to detect all states."VARIATION ifLastChange
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces, lex based interfaces
used for accounting and in cable, mc3810_dsx1, voice
subinterfaces."VARIATION ifInOctets
ACCESSread-onlyDESCRIPTION"Not supported in atm sublayer on an ATM
end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an
ATM switch CPU interface, aal5 sublayer on
the atm interfaces of an ATM end system,
AIP type aal5 sublayer on an ATM end system and in
frame-relay, x25, aflane, cable subinterfaces."VARIATION ifInUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane, cable
subinterfaces."VARIATION ifInNUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifInDiscards
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifInErrors
ACCESSread-only
DESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifInUnknownProtos
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutOctets
ACCESSread-onlyDESCRIPTION"Not supported in atm sublayer on an ATM end system.
Supported in physical interfaces, lex based interfaces,
aal5 sublayer of an ATM switch CPU interface,
aal5 sublayer on the atm interfaces of an ATM
end system, AIP type aal5 sublayer on an ATM
end system and in frame-relay, x25, aflane,
cable subinterfaces."VARIATION ifOutUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutNUcastPkts
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces, lex based accounting
interfaces and in aflane subinterfaces."VARIATION ifOutDiscards
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutErrors
ACCESSread-only
DESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutQLen
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifSpecific
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifInMulticastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifInBroadcastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifOutMulticastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifOutBroadcastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifHCInOctets
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces and
LEC sub-layers."VARIATION ifHCInUcastPkts
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces."VARIATION ifHCInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCInBroadcastPkts
ACCESSnot-implementedDESCRIPTION
"Not supported."VARIATION ifHCOutOctets
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces and
in LEC sub-layers."VARIATION ifHCOutUcastPkts
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces."VARIATION ifHCOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifLinkUpDownTrapEnable
ACCESSread-writeDESCRIPTION"Physical interfaces and subinterfaces can have link
traps enabled. Write not supported in lex based
interfaces used for accounting and the object is
hardwired to be false."VARIATION ifPromiscuousMode
SYNTAXTruthValueACCESSread-onlyDESCRIPTION"Not writable, hardcoded to false (2)."VARIATION ifConnectorPresent
ACCESSread-onlyDESCRIPTION"Hardcoded to be false on lex based interfaces
used for accounting."VARIATION ifAlias
SYNTAXDisplayString(SIZE(0..64))ACCESSread-writeDESCRIPTION"For interfaces that are not being nv written,
the ifAlias value is lost when the system
is reloaded."VARIATION ifCounterDiscontinuityTime
ACCESSnot-implemented
DESCRIPTION"Not supported."VARIATION ifStackStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Write/create not supported.
Unable to detect all states."VARIATION ifRcvAddressAddress
DESCRIPTION"Read-only access is added to this object.
Supported in physical interfaces,
lex based interfaces and in lec
sublayers."VARIATION ifRcvAddressStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Write/create not supported. Unable to
detect all states. Supported in physical
interfaces, lex based interfaces and in
lec sublayers."VARIATION ifRcvAddressType
SYNTAXINTEGER{
other(1)}ACCESSread-onlyDEFVAL{ other }DESCRIPTION"Write/create not supported. Unable to detect
all states. Default value is { other }.
Supported in physical interfaces, lex based
interfaces and in lec sublayers."VARIATION ifTestId
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestStatus
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestType
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestResult
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestCode
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestOwner
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION linkUp
DESCRIPTION"A linkUp trap signifies that the sending
protocol entity recognizes that one of the
communication links represented in the agent's
configuration has come up."VARIATION linkDown
DESCRIPTION"A linkDown trap signifies that the sending
protocol entity recognizes a failure in one of
the communication links represented in the
agent's configuration."::={ ciscoIfCapability 2}ciscoIfCapabilityV12R01T AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco IOS 12.1T"STATUScurrentDESCRIPTION"IF MIB capabilities"SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifStackGroup2,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifRcvAddressGroup,
ifOldObjectsGroup
}VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"OIR instances need to be modified"VARIATION ifAdminStatus
ACCESSread-writeDESCRIPTION"Can not be written in case of atm/aal5 sublayers
on an ATM end system, LEC subinterfaces, aal5
sublayer of an ATM switch CPU interface, ATM 2000
physical interface and lex based interfaces
used for accounting."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3),
unknown(4),
dormant(5)}DESCRIPTION
"Unable to detect all states."VARIATION ifLastChange
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces, lex based
interfaces used for accounting and in cable,
mc3810_dsx1, voice subinterfaces."VARIATION ifInOctets
ACCESSread-onlyDESCRIPTION"Not supported in atm sublayer on an ATM end system.
Supported in physical interfaces, lex based interfaces,
aal5 sublayer of an ATM switch CPU interface,
aal5 sublayer on the atm interfaces of an ATM
end system, AIP type aal5 sublayer on an ATM
end system and in frame-relay, x25,
aflane, cable subinterfaces."VARIATION ifInUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifInNUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifInDiscards
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifInErrors
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifInUnknownProtos
ACCESSread-only
DESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutOctets
ACCESSread-onlyDESCRIPTION"Not supported in atm sublayer on an ATM end system.
Supported in physical interfaces, lex based interfaces,
aal5 sublayer of an ATM switch CPU interface,
aal5 sublayer on the atm interfaces of an
ATM end system, AIP type aal5 sublayer on an
ATM end system and in frame-relay, x25,
aflane, cable subinterfaces."VARIATION ifOutUcastPkts
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutNUcastPkts
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces, lex based
accounting interfaces and in aflane subinterfaces."VARIATION ifOutDiscards
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutErrors
ACCESSread-onlyDESCRIPTION"Not supported in frame-relay subinterfaces,
x25 subinterfaces, atm/aal5 sublayers on an
ATM end system. Supported in physical interfaces,
lex based interfaces, aal5 sublayer of an ATM
switch CPU interface and in aflane,
cable subinterfaces."VARIATION ifOutQLen
ACCESSread-only
DESCRIPTION"Not supported in subinterfaces."VARIATION ifSpecific
ACCESSread-onlyDESCRIPTION"Not supported in subinterfaces."VARIATION ifInMulticastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifInBroadcastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifOutMulticastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifOutBroadcastPkts
ACCESSread-onlyDESCRIPTION"Supported in cable subinterface."VARIATION ifHCInOctets
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces and
LEC sub-layers."VARIATION ifHCInUcastPkts
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces."VARIATION ifHCInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCInBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCOutOctets
ACCESSread-onlyDESCRIPTION"Supported in physical interfaces and
in LEC sub-layers."VARIATION ifHCOutUcastPkts
ACCESSread-onlyDESCRIPTION
"Supported in physical interfaces."VARIATION ifHCOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifHCOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifLinkUpDownTrapEnable
ACCESSread-writeDESCRIPTION"Physical interfaces and subinterfaces can have link
traps enabled. Write not supported in lex based
interfaces used for accounting and the object is
hardwired to be false."VARIATION ifPromiscuousMode
SYNTAXTruthValueACCESSread-onlyDESCRIPTION"Not writable, hardcoded to false (2)."VARIATION ifConnectorPresent
ACCESSread-only
DESCRIPTION"Hardcoded to be false on lex based
interfaces used for accounting."VARIATION ifAlias
SYNTAXDisplayString(SIZE(0..64))ACCESSread-writeDESCRIPTION"For interfaces that are not being nv written,
the ifAlias value is lost when the system
is reloaded."VARIATION ifStackStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Write/create not supported.
Unable to detect all states."VARIATION ifRcvAddressAddress
DESCRIPTION
"Read-only access is added to this object.
Supported in physical interfaces, lex based
interfaces and in lec sublayers."VARIATION ifRcvAddressStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Write/create not supported. Unable to detect
all states. Supported in physical interfaces,
lex based interfaces and in lec sublayers."VARIATION ifRcvAddressType
SYNTAXINTEGER{
other(1)}ACCESSread-onlyDEFVAL{ other }DESCRIPTION"Write/create not supported. Unable to detect
all states. Default value is { other }.
Supported in physical interfaces,
lex based interfaces and in lec sublayers."VARIATION ifTestId
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestStatus
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestType
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestResult
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestCode
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestOwner
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION linkUp
DESCRIPTION"A linkUp trap signifies that the sending
protocol entity recognizes that one of the
communication links represented in the agent's
configuration has come up. When a new config
command 'snmp-server trap link ietf' is set, the
varbind list is made of objects specified here.
Otherwise, the varbind list defined in the
previous version holds good. For sub-interfaces,
as there is no support for locIfReason, it will
be omitted from the trap message."VARIATION linkDown
DESCRIPTION"A linkDown trap signifies that the sending
protocol entity recognizes a failure in one of
the communication links represented in the
agent's configuration. When a new config
command 'snmp-server trap link ietf' is set, the
varbind list is made of objects specified here.
Otherwise, the varbind list defined in the
previous version holds good. For sub-interfaces,
as there is no support for locIfReason, it will
be omitted from the trap message."::={ ciscoIfCapability 3}ciscoIfCapabilityPxmVR200 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 2.00,BPX SES Release 1.00."STATUScurrentDESCRIPTION"IF MIB capabilities for PXM45, PXM1 Modules."SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifPacketGroup
}VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
DESCRIPTION"This object can not be written in case of
rs232 interface identified by ifType
value rs232(33)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3)}DESCRIPTION"Unable to detect all states."VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifInOctets
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifInUcastPkts
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifInDiscards
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifInErrors
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifInUnknownProtos
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifOutOctets
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifOutUcastPkts
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifOutDiscards
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifOutErrors
DESCRIPTION"Supported only for following interfaces:
Ethernet interface (ifType = ethernetCsmacd(6))
Loopback interfce (ifType = softwareLoopback(24))
SLIP Interface (ifType = slip(28))."VARIATION ifInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifInBroadcastPkts
ACCESSnot-implemented
DESCRIPTION"Not supported."VARIATION ifOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDEFVAL{ disabled }DESCRIPTION"Write operation not supported."VARIATION ifPromiscuousMode
ACCESSread-onlyDEFVAL{ false }DESCRIPTION"Write operation not supported."VARIATION ifAlias
ACCESSnot-implemented
DESCRIPTION"Not supported."::={ ciscoIfCapability 4}ciscoIfCapabilityAxsmVR200 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 2.00."STATUScurrentDESCRIPTION"IF MIB capabilities for ATM Switch Service
Module(AXSM)."SUPPORTS IF-MIB
INCLUDES{ ifGeneralInformationGroup }VARIATION ifNumber
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifPhysAddress
ACCESSnot-implemented
DESCRIPTION"Not supported."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"This object can not be written in case of
atm interface identified by ifType value atm(37).
Does not support testing(3)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
notPresent(6)}DESCRIPTION"Unable to detect all states.
Does not support testing(3),unknown(4),
dormant(5),lowerLayerDown(7)."
VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDEFVAL{ disabled }DESCRIPTION"Write operation not supported."VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported."::={ ciscoIfCapability 5}ciscoIfCapabilityAxsmeV21R60 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 2.1.60"STATUScurrentDESCRIPTION"IF MIB capabilities for Enhanced ATM
Switch Service Module (AXSM-E)."SUPPORTS IF-MIB
INCLUDES{ ifGeneralInformationGroup }VARIATION ifNumber
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Does not support testing(3)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
notPresent(6),
lowerLayerDown(7)}DESCRIPTION"Unable to detect all states.
Does not support testing(3),
unknown(4), dormant(5)."VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDEFVAL{ disabled }DESCRIPTION"Write operation not supported."VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported."::={ ciscoIfCapability 6}ciscoIfCapabilityFrsm12V3R00 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 3.0.00"STATUScurrentDESCRIPTION"IF MIB capabilities for
Frame Relay Service Module(FRSM-12)."SUPPORTS IF-MIB
INCLUDES{ ifGeneralInformationGroup }VARIATION ifNumber
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Does not support testing(3)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
notPresent(6),
lowerLayerDown(7)}DESCRIPTION"Unable to detect all states.
Does not support testing(3),
unknown(4), dormant(5)."VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDEFVAL{ disabled }DESCRIPTION"Write operation not supported."VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported."::={ ciscoIfCapability 7}ciscoIfCapabilityV4R00 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8950, MGX8850 Release 4.0.00"STATUScurrentDESCRIPTION"IF MIB capabilities for 10 Gig. ATM
Switch Service Module (AXSM-XG) and
Enhanced ATM Switch Service Module
(AXSM-E)."SUPPORTS IF-MIB
INCLUDES{ ifGeneralInformationGroup }VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3),
notPresent(6),
lowerLayerDown(7)}DESCRIPTION"Only subset of values supported.
Following values not supported:
unknown(4), dormant(5)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
notPresent(6),
lowerLayerDown(7)}DESCRIPTION"Only subset of values supported.
Following values not supported:
testing(3), unknown(4), dormant(5)."VARIATION ifNumber
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Does not support testing(3)."VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDEFVAL{ disabled }DESCRIPTION"Write operation not supported."VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported."::={ ciscoIfCapability 8}
ciscoIfCapabilityV5R00 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 5.0.0"STATUScurrentDESCRIPTION"IF MIB capabilities for Voice Switch
Service Module (VXSM) and MPSM in
release 5.0.0"SUPPORTS IF-MIB
INCLUDES{ ifGeneralInformationGroup }VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifNumber
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"For ifType propAtm (197), only up(1) is supported.
This object is not supported if the
ifType is sonetVT(51)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"For ifType propAtm (197), not all states
can be detected.
This object is not supported if the ifType
is sonetVT(51) or propAtm (197)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3),
notPresent(6),
lowerLayerDown(7)}DESCRIPTION"For ifType propAtm (197), not all states
can be detected.
For ifType sonetVT(51) only up(1), down(2) and
lowerLayerDown(7) are detected."VARIATION ifLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifLinkUpDownTrapEnable
ACCESSread-only
DEFVAL{ disabled }DESCRIPTION"Write operation not supported."::={ ciscoIfCapability 9}ciscoIfCapabilityCatOSV08R0101 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco CatOS 8.1(1) on Catalyst 6000/6500
and Cisco 7600 series devices."STATUScurrentDESCRIPTION"IF MIB agent capabilities."SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifStackGroup2,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifOldObjectsGroup,
ifCounterDiscontinuityGroup,
linkUpDownNotificationsGroup,
ifGeneralGroup,
ifStackGroup
}VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Set operations are not allowed on VLAN
interfaces, EtherChannel interfaces,
subinterfaces, and ports of network
service modules."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
dormant(5),
lowerLayerDown(7)}DESCRIPTION"Always returns up(1) for VLAN interfaces."VARIATION ifInOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifInUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifInNUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifInDiscards
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifInErrors
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifInUnknownProtos
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifOutOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifOutUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifOutNUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifOutDiscards
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifOutErrors
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifOutQLen
DESCRIPTION"Hardcoded to zero."VARIATION ifSpecific
DESCRIPTION"Hardcoded to nullOID."VARIATION ifInMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces, i.e.,
the in-band interfaces(sc0 and sc1) and
the out-of-band management serial line
internet protocol(SLIP) interface(sl0)."VARIATION ifInBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces."VARIATION ifOutMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces."VARIATION ifOutBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces."VARIATION ifHCInOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifHCInUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifHCInMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifHCInBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."
VARIATION ifHCOutOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifHCOutUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifHCOutMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifHCOutBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces."VARIATION ifLinkUpDownTrapEnable
DESCRIPTION"Set operations are not allowed on VLAN
interfaces, ports of network service
modules and subinterfaces."VARIATION ifPromiscuousMode
DESCRIPTION"Set operations are not allowed."VARIATION ifAlias
DESCRIPTION"Set operations not allowed on subinterfaces."VARIATION ifStackStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Supported for EtherChannel interfaces only.
Unable to detect all states.
Set operations are not allowed."VARIATION ifRcvAddressStatus
ACCESSnot-implementedDESCRIPTION"Table for ifRcvAddressEntry not supported."VARIATION ifRcvAddressType
ACCESSnot-implementedDESCRIPTION"Table for ifRcvAddressEntry not supported."VARIATION ifTestId
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestStatus
ACCESSnot-implemented
DESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestType
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestResult
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestCode
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestOwner
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION linkUp
DESCRIPTION"The instance value for ifName is appended
in addition to the regular varbinds."
VARIATION linkDown
DESCRIPTION"The instance values of
portSecurityOperStatus and
portSecurityLastSrcAddr are appended in
case of port security issues, and the
instance value of portAdditionalOperStatus
upon port errordisable issues."::={ ciscoIfCapability 10}ciscoIfCapabilityCatOSV08R0301 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco CatOS 8.3(1) on Catalyst 6000/6500
and Cisco 7600 series devices."STATUScurrentDESCRIPTION"IF MIB agent capabilities."SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifStackGroup2,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifOldObjectsGroup,
ifCounterDiscontinuityGroup,
linkUpDownNotificationsGroup,
ifGeneralGroup,
ifStackGroup
}VARIATION ifMtu
DESCRIPTION"Hardcoded to zero for the inband port."VARIATION ifPhysAddress
DESCRIPTION"Hardcoded to '00 00 00 00 00 00' for the
inband port."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Set operations are not allowed on VLANs,
EtherChannel interfaces, the inband port,
subinterfaces, and ports of network
service modules."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
dormant(5),
lowerLayerDown(7)}DESCRIPTION"Always returns up(1) for the inband port
and VLAN interfaces."VARIATION ifInOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces
if PFC(Policy Feature Card) 1 is used.
Hardcoded to zero for the inband port."VARIATION ifInUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 is used. Not instantiated for the
inband port."VARIATION ifInNUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 is used. Not instantiated for the
inband port."VARIATION ifInDiscards
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifInErrors
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifInUnknownProtos
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifOutOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 or PFC 2 is used. Not instantiated for
the inband port."VARIATION ifOutUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 is used. Not instantiated for the
inband port."VARIATION ifOutNUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 or PFC 2 is used. Not instantiated for
the inband port."VARIATION ifOutDiscards
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifOutErrors
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifOutQLen
DESCRIPTION"Hardcoded to zero."VARIATION ifSpecific
DESCRIPTION"Hardcoded to nullOID."VARIATION ifInMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces. Not
instantiated for the inband port."VARIATION ifInBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces. Not
instantiated for the inband port."VARIATION ifOutMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces. Not
instantiated for the inband port."VARIATION ifOutBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces and
switch management interfaces. Not
instantiated for the inband port."VARIATION ifHCInOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 is used. Not instantiated for the
inband port."VARIATION ifHCInUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 in use. Not instantiated for the
inband port."VARIATION ifHCInMulticastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifHCInBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifHCOutOctets
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 or PFC 2 is used. Not instantiated for
the inband port."VARIATION ifHCOutUcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces if
PFC 1 is used. Not instantiated for the
inband port."VARIATION ifHCOutMulticastPkts
DESCRIPTION"Not instantiated for the inband port."VARIATION ifHCOutBroadcastPkts
DESCRIPTION"Hardcoded to zero for VLAN interfaces. Not
instantiated for the inband port."VARIATION ifLinkUpDownTrapEnable
DESCRIPTION"Not instantiated for the inband port.
Set operations are not allowed on VLAN
interfaces, ports of network service
modules and subinterfaces."VARIATION ifHighSpeed
DESCRIPTION"Hardcoded to zero for the inband port."VARIATION ifPromiscuousMode
DESCRIPTION"Set operations are not allowed."VARIATION ifAlias
DESCRIPTION"Always returns an empty string for the
inband port. Set operations not allowed on
subinterfaces and the inband port."VARIATION ifStackStatus
SYNTAXINTEGER{
active(1)}ACCESSread-onlyDESCRIPTION"Supported for EtherChannel interfaces only.
Unable to detect all states.
Set operations are not allowed."VARIATION ifRcvAddressStatus
ACCESSnot-implementedDESCRIPTION"Table for ifRcvAddressEntry not supported."
VARIATION ifRcvAddressType
ACCESSnot-implementedDESCRIPTION"Table for ifRcvAddressEntry not supported."VARIATION ifTestId
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestStatus
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestType
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestResult
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestCode
ACCESSnot-implemented
DESCRIPTION"Table for ifTestEntry not supported."VARIATION ifTestOwner
ACCESSnot-implementedDESCRIPTION"Table for ifTestEntry not supported."VARIATION linkUp
DESCRIPTION"The instance value for ifName is appended
in addition to the regular varbinds."VARIATION linkDown
DESCRIPTION"The instance values of
portSecurityOperStatus and
portSecurityLastSrcAddr are appended in
case of port security issues, and the
instance value of portAdditionalOperStatus
upon port errordisable issues."::={ ciscoIfCapability 11}ciscoIfCapabilityV5R015 AGENT-CAPABILITIESPRODUCT-RELEASE"MGX8850 Release 5.0.15"STATUScurrent
DESCRIPTION"IF MIB capabilities for Voice Switch
Service Module (VXSM) 5.0.15"SUPPORTS IF-MIB
INCLUDES{ ifGeneralInformationGroup }VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifNumber
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}
DESCRIPTION"For ifType propAtm (197), only up(1) is supported.
This object is not supported if the
ifType is sonetVT(51) or lapd(24)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"For ifType propAtm (197), not all states
can be detected.
This object is not supported if the ifType
is sonetVT(51) or propAtm (197) or lapd(24)."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2),
testing(3),
notPresent(6),
lowerLayerDown(7)}DESCRIPTION"For ifType propAtm (197), not all states
can be detected.
For ifType sonetVT(51) only up(1), down(2) and
lowerLayerDown(7) are detected."VARIATION ifType
DESCRIPTION"Only support the following ifType:
sonet(39)
sonetPath(50)
ds3(30)
vtPath(51)
ds1(18)
propAtm(197)
AtmVciEp(194)
lapd(77)"VARIATION ifLastChange
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifLastChange
DESCRIPTION"The value does not reflect the change in
the operational status of the interface.
The value zero is returned."VARIATION ifLinkUpDownTrapEnable
ACCESSread-only
DEFVAL{ disabled }DESCRIPTION"Write operation not supported."VARIATION ifLinkUpDownTrapEnable
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported."VARIATION ifConnectorPresent
ACCESSnot-implementedDESCRIPTION"Not supported."::={ ciscoIfCapability 12}ciscoIfCapabilityIOSXRV2R0CRS1 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco IOS XR 2.0 for CRS-1"STATUScurrentDESCRIPTION
"IF-MIB capabilities for Cisco IOS
XR in releases 2.0"SUPPORTS IF-MIB
INCLUDES{
ifGeneralGroup,
ifStackGroup,
ifGeneralInformationGroup,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifStackGroup2,
ifCounterDiscontinuityGroup
}VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifPromiscuousMode
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifConnectorPresent
ACCESSnot-implementedDESCRIPTION"Not supported"::={ ciscoIfCapability 13}ciscoIfCapabilityACSWV03R000 AGENT-CAPABILITIESPRODUCT-RELEASE"ACSW (Application Control Software) 3.0
for Application Control Engine (ACE)
Service Module."STATUScurrentDESCRIPTION"IF-MIB capabilities for Cisco ACSW 3.0."SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
linkUpDownNotificationsGroup
}
VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}ACCESSread-onlyDESCRIPTION"Only up(1) and down(2) states are supported.
Set operation not allowed."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Only up(1) and down(2) states are supported."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDESCRIPTION"Set operation not allowed."
VARIATION ifAlias
ACCESSread-onlyDESCRIPTION"Maximum length supported is 240 characters.
Set operation not allowed."VARIATION ifPromiscuousMode
SYNTAXTruthValueACCESSread-onlyDESCRIPTION"The only value supported is false(2)."VARIATION linkUp
DESCRIPTION"A linkUp notification signifies that the sending
protocol entity recognizes that one of the
communication links represented in the agent's
configuration has come up. By default all
varbinds listed under the OBJECTS clause
are included in the notification PDU. When a
new configuration command 'snmp-server trap link
ietf' is set, varbinds ifType, ifName,
clogOriginIDType, clogOriginID are not included
in the notification PDU."VARIATION linkDown
DESCRIPTION"A linkDown notification signifies that the sending
protocol entity recognizes a failure in one of
the communication links represented in the
agent's configuration. By default all
varbinds listed under the OBJECTS clause
are included in the notification PDU. When a new
configuration command 'snmp-server trap link
ietf' is set, varbinds ifType, ifName,
clogOriginIDType, clogOriginID are not included
in the notification PDU."::={ ciscoIfCapability 14}ciscoIfCapabilityCTSV100 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco TelePresence System (CTS) 1.0.0"STATUScurrentDESCRIPTION"IF-MIB capabilities for CTS 1.0.0"SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifFixedLengthGroup,
ifPacketGroup
}VARIATION ifLastChange
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifLinkUpDownTrapEnable
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifConnectorPresent
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifHighSpeed
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifName
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifInUnknownProtos
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifInBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifPromiscuousMode
ACCESSnot-implementedDESCRIPTION"Not supported"::={ ciscoIfCapability 15}ciscoIfCapabilityCTMV1000 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco TelePresence Manager (CTM) 1.0.0.0"STATUScurrentDESCRIPTION"IF-MIB capabilities for CTM 1.0.0.0"SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifFixedLengthGroup,
ifPacketGroup
}VARIATION ifLastChange
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifLinkUpDownTrapEnable
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifConnectorPresent
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifHighSpeed
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifName
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifAlias
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifTableLastChange
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifInUnknownProtos
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifInMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifInBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifOutMulticastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifOutBroadcastPkts
ACCESSnot-implementedDESCRIPTION"Not supported"VARIATION ifPromiscuousMode
ACCESSnot-implementedDESCRIPTION"Not supported"::={ ciscoIfCapability 16}
ciscoIfCapabilityIOSXRV3R4CRS1 AGENT-CAPABILITIESPRODUCT-RELEASE"Cisco IOS XR 3.4 for CRS-1"STATUScurrentDESCRIPTION"IF-MIB capabilities for Cisco IOS
XR in releases 3.4"SUPPORTS IF-MIB
INCLUDES{
ifGeneralGroup,
ifStackGroup,
ifGeneralInformationGroup,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
ifVHCPacketGroup,
ifStackGroup2,
ifCounterDiscontinuityGroup,
ifRcvAddressGroup
}VARIATION ifPhysAddress
ACCESSnot-implementedDESCRIPTION"Not supported"::={ ciscoIfCapability 17}ciscoIfCapabilityc4710aceVA1R700 AGENT-CAPABILITIESPRODUCT-RELEASE"ACSW (Application Control Software) A1(7)
for ACE 4710 Application Control Engine
Appliance"STATUScurrentDESCRIPTION"IF-MIB capabilities for Cisco ACSW A1(7)"SUPPORTS IF-MIB
INCLUDES{
ifGeneralInformationGroup,
ifFixedLengthGroup,
ifHCFixedLengthGroup,
ifPacketGroup,
ifHCPacketGroup,
linkUpDownNotificationsGroup
}VARIATION ifAdminStatus
SYNTAXINTEGER{
up(1),
down(2)}ACCESSread-onlyDESCRIPTION"Only up(1) and down(2) states are supported.
Set operation not allowed."VARIATION ifOperStatus
SYNTAXINTEGER{
up(1),
down(2)}DESCRIPTION"Only up(1) and down(2) states are supported."VARIATION ifLinkUpDownTrapEnable
ACCESSread-onlyDESCRIPTION"Set operation not allowed."
VARIATION ifAlias
ACCESSread-onlyDESCRIPTION"Maximum length supported is 240 characters.
Set operation not allowed."VARIATION ifPromiscuousMode
SYNTAXTruthValueACCESSread-onlyDESCRIPTION"The only value supported is false(2)."VARIATION linkUp
DESCRIPTION"A linkUp notification signifies that the sending
protocol entity recognizes that one of the
communication links represented in the agent's
configuration has come up. By default all
varbinds listed under the OBJECTS clause
are included in the notification PDU. When a
new configuration command 'snmp-server trap link
ietf' is set, varbinds ifType, ifName,
clogOriginIDType, clogOriginID are not included
in the notification PDU."VARIATION linkDown
DESCRIPTION"A linkDown notification signifies that the sending
protocol entity recognizes a failure in one of
the communication links represented in the
agent's configuration. By default all
varbinds listed under the OBJECTS clause
are included in the notification PDU. When a new
configuration command 'snmp-server trap link
ietf' is set, varbinds ifType, ifName,
clogOriginIDType, clogOriginID are not included
in the notification PDU."::={ ciscoIfCapability 18}END